Replace an iPhone 3G Intalling the Volume Button Manual Guide
TOOLS:
Phillips 00 Screwdriver (1)
Small suction cup (1)
Spudger (1)
iPod Opening Tools (1)
PARTS:
iPhone 3G and 3GS Volume Button (1)
OVERVIEW
This guide allows the cover of plastic volume, not the electronic volume buttons
the switches themselves.
Step 1 â€" battery
Remove the two screws from 3.7 mm socket Phillips #00
end of the iPhone .
Step 2
Remove the metal and the handle. It is easier and safer to hold on to the base of the Cup instead of the metal handle. Be very careful when opening the iPhone so don’t break the wires under the screen. There is a rubber between the facade silver
bezel and black screen Assembly. A little force is necessary in this
step away from the iPhone screen. Use a small cup beside the Start button to gently pull the bottom of the whole of the iPhone screen. If the screen is too damaged to allow the suction cup, the tape can be used with adhesive tape and glue strong.
Step 3
Screen is still connected to the iPhone by several cables, then do not attempt to remove completely the immediate. Turn the screen until it forms an angle of approximately 45 degrees.
Step 4
They continue to hold the screen with one hand and use the other hand and a spudger to disconnect the black cable marked ’1′. (Cable 1 is for display) Be sure to insert the spudger from left to right, as shown in the image (such as tape). If you try to lift the right tape, you may damage the tape
Connector and the need to replace the screen! All connectors except the
Ribbon connector had mentioned in step 6 exit upwards.
Step 5
Screen rotation until it is almost vertical. This will allow easier access to disconnect the remaining wires.
Use a spudger to disconnect the black wire marked ’2′.
(2 Cable is for capacitive touch screen)
Step 6
Please note: you will find in some versions of not-American (Chinese, European) 3 g that they return the plastic tab does not exist. In this case slide the ribbon cable to the screen until it is removed. When you assemble it, apply pressure to the
Ribbon to insert the tape “socketâ€. Some iPhones may have the reverse connector colors (black, white plastic connector tab) for the connector «3». Make sure that you’re flipping upwards on the tab
correctly, otherwise you may damage the connector. Use a spudger to lift the white plastic tab now ’3′ water instead. The white tab rotates 90 degrees, to release the ribbon cable.
Drag the black cable to its connector and remove the
Show an Assembly from the iPhone.
Step 7
Insert your SIM eject tool or a paper clip into the hole next to the
headphone output. Press the tool until it leaves the SIM card tray. Insert the SIM card tray in and out of the iPhone.
Step 8
Use a spudger to disconnect the cable with the label “4.â€
Step 9
Use a spudger to disconnect the cable with the label “5.â€
Step 10
Use a spudger to disconnect the cable labeled “6.†If you have a 3 g iPhone, refer to the second image and use a spudger to disconnect the cable labeled “7.â€
Step 11
Carefully Peel up the small sticker label “remove.â€
Step 12
Remove the 8 screws following: five 2.3 mm partial safety of the screw thread #00 Phillips of the logic board to the new box. Two 2.3 mm Phillips #00 screws with thread full ensuring the logic board and the Chamber. 2.9 Mm Phillips #00 screws under the label “do not removeâ€. Note to reassemble: screw that goes along with the camera (right bottom screw Orange highlighted) also has a metal band that holds the camera in place. Don’t forget to replace this band
in place before inserting the 2.3 mm Phillips #00 screws with full
wire close to the camera
Step 13
Use a spudger to lift carefully upwards and out of the House Chamber in the
the back of the housing. The camera can be removed completely, but because that is connected at the bottom of the logic board.Step 14
Use a spudger to gently lift from the nearest end of the logical path
the dock dock connector. Is a small golden land on the map tab logic adjacent to the “do not remove label. Beware of do not hang on the side of the box when the eyes to the top of the logic board; It breaks easily. If you have signal problems after removing the logic board, check this tab of the Earth. If the jury is lift,
Check to make sure that all screws securing the system board are removed.
Step 15
Drag the logic board to the connector dock and customers of the
iPhone. When overriding the logical adapter after installing the battery, connect the device to the logic board beforeinsert ing in the case. Then åke course to fix the upper part of the logic card (where is the SIM tray) in place before spending the rest of the Board of Directors in place. It is important, since sometimes the SIM card slot snap into place. Once up, the bottom can be manipulated in place. You know that logical adapter is correctly installed when the SIM tray is aligned with the opening for the camera and iPhone module seats perfectly into place.
Step 16
Use a spudger to the battery on the back cover. The battery is secured with tape around the perimeter of the battery. To prevent the battery during the bending process, we do not recommend the use of only the plastic tab.
* Note: Remove the battery is not necessary to replace the
GPS antenna. Gives you more space simply to eliminate the
Assembly of headset (which is also not necessary to completely remove).
IPhone battery is attached to the rear box with a soft xdhesive. This released adhesive usually connected to the battery. If the replacement battery already includes a tape, that’s all. If your replacement battery isn’t an adherent, he wishes you to transfer your old battery of new adhesive. You can use a hair dryer or a heat gun at their lowest level
adjust to heat the back part of the nacelle. This will help to loosen the
before use the spudger bonding to separate battery
from the bottom of the housing.
Remove step 17 â€" Headphone Jack
the two Phillips #00 flange fastening screws switch. For replacement, check the bump on the switch. There is a small piece of plastic stuck inside the button that can come with cleaning. Without a spacer, the button not can extend far enough to be depressed. If you lose, you can measure with a suitable thickness of rigid plastic (e.g. top shirt box).
Step 18
Carefully Peel the Orange cable of the back cover.
Water damaged easily â€" very soft.
Step 19
Remove the 4 screws following: three 1.8 mm recessed #00 ensure the headphone socket and a GPS antenna to box again. Note the order in which you remove screws, as the left has a slightly larger head. A 3.8 mm Phillips #00 screw into the plastic buckle close the headphone output.
Step 20
Phillips remove four screws #00 set the volume and the ‘secret’. The mounting of the volume switch is located in the upper part of the ‘secret’ key. Make sure that the small soft cushion in the “secret†key is not lost, otherwise the ‘secret’ key will remain very freely after re-Assembly.
The ‘secret’ key bolts with switch
in the off position. Check extrusion of the switch when you change, because enough does not adhere to work if the switch Assembly is positioned incorrectly. (Check clearance between the frame of the switch and bezel (white gap between the two screws near the 6). The screw located on the extreme right is slightly longer than the other 3 screws. When you reassemble the phone, take it into account.
Step 21
Lift circuit volume button on the side of the iPhone and carefully Peel the Orange cable of the back cover. The cable is fine and easily damaged.
Step 22
Carefully lift the connector of the iPhone headphones. Mute switch green down (toward the back of the iPhone) in silent position. This will make it easier to insert, once the new mute button is in place.
Volume 23-step button
If they have not already fallen back cover, remove the mute and power button.
Step 24
Phillips #00 remove two screws the vibrator in the back of the Panel. Remove the vibrator on the back
Step 25
Remove the 3 screws of the following: 1.5 mm Phillips #00 screws, one on each side of the dock connector. 2-4 mm Phillips #00 screws near the water with the label “4.†Unpack all the dock connector dock to the top of the iPhone. In the inclusion of the new Assembly, ensure that holes remains above the holes in the bezel.
Step 26
In the following steps, you partly remove the silver bezel attached on the back. If the residual glue is not enough to keep together for reassembly, it may be necessary to apply a light layer of glue around the inside edge of the bezel to maintain
It is protected against the back. Insert the edge of a tool to open the iPod in the gap between the silver bezel and the facade of the side volume key on the telephone. Run on the edge of the cut along the seam tool to separate the two components. The aim is to lift silver bezel enough to push button volume on back cover.
Step 27
Once they have erected enough bezel silver to release the volume button, use the edge of the opening tool to press the volume button towards the inside of the back panel. Delete the volume knob.
Reassemble the appliance, follow these instructions in reverse order.
No comments:
Post a Comment